Welcome, Guest. Please Login or Register
VeeCAD Stripboard Editor
   
  HomeHelpSearchLoginRegister  
 
Page Index Toggle Pages: 1
Send Topic Print
Trackless holding area for components (Read 3268 times)
dsimsj
YaBB Newbies
*
Offline


Your message here...

Posts: 26
Trackless holding area for components
Jun 15th, 2015 at 10:23pm
 
Hi Roger,
Way back in June 2011 (I didn't think it was that long ago - time really flies for us oldies!) I suggested that some sort of holding area for components that didn't generate connection errors would be a nice feature to make layouts easier, especially at the start of a layout when rat lines and error blobs abound.
Well I think one of your latest features, namely the Track Editor, has produced this as a side effect.
The attached pdf shows how I achieved creating and using such an area.
Many thanks.
Best regards
Dave
Back to top
 
 
IP Logged
 
Roger Lascelles
Administrator
*****
Offline



Posts: 409
Ocean Grove, Australia
Re: Trackless holding area for components
Reply #1 - Jun 16th, 2015 at 12:25pm
 
Hello Dave
  • Thank you for taking the time to document your technique. i know others will find it helpful
  • VeeCAD needs something like this as a built in feature. For example, a side panel that you can drag parts to. I can't say if or when I can work on it, due to tricky circumstances.
Back to top
 

Roger
 
IP Logged
 
HELLI
YaBB Newbies
*
Offline


Your message here...

Posts: 41
Ireland
Re: Trackless holding area for components
Reply #2 - Jun 16th, 2015 at 12:32pm
 
Hi Dave,
At times I have wanted to have a component overhang the edge of the board and I had to allow an extra strip to do this. Usually something like a coin-cell holder. Now with the editor you can move all the tracks left/right or up/down by using the drag select and moving them.

Great work Roger!
Thanks!

Hamilton
Back to top
 
 
IP Logged
 
Roger Lascelles
Administrator
*****
Offline



Posts: 409
Ocean Grove, Australia
Re: Trackless holding area for components
Reply #3 - Jun 16th, 2015 at 2:49pm
 
Hello Hamilton

It must have been you who asked for components to overlap the board edge. I knew the Track Editor would solve that problem for free.

I have just realised that if VeeCAD were to allow parts to go off-board, it would achieve the effect that Dave is talking about, without needing to use the Track Editor. Parts off-board is a matter of reworking the movement limits in the code. I'll put it on the list of good ideas. I am very aware that my imagination ran out years ago, and that it is only user suggestions that give me a new insight.
Back to top
 

Roger
 
IP Logged
 
dsimsj
YaBB Newbies
*
Offline


Your message here...

Posts: 26
Re: Trackless holding area for components
Reply #4 - Jul 2nd, 2015 at 8:57am
 
Hi Roger,
I've only just seen your reply on the 16th to my original post and I do hope that your "tricky circumstances" are not too awful for you.
I think I speak for all users of VeeCad when I say it is one of the best and most useful pieces of software that I have used in years and your support for it has been second to none.
My very best regards
Dave
Back to top
 
 
IP Logged
 
Roger Lascelles
Administrator
*****
Offline



Posts: 409
Ocean Grove, Australia
Re: Trackless holding area for components
Reply #5 - Jul 2nd, 2015 at 10:19am
 
Thanks Dave. Nothing serious. Just can't find uninterupted time or a quiet place to get much work done at present.
Back to top
 

Roger
 
IP Logged
 
Mnementh
YaBB Newbies
*
Offline


Your message here...

Posts: 12
Dundee, Scotland
Re: Trackless holding area for components
Reply #6 - Apr 7th, 2016 at 12:36pm
 
HI all,
a very interesting side effect and a comprehensive PDF showing "how it's done".

I tried it and found it worked well but I noted one minor issue.

That is that when you "achieve" the blank area, you're basically stuck with the tracks as you've set them.

Yes, you can "stretch" the track lengths back to full width but when you resize the board, all you generate is "blank" space with the tracks unchanged.

The only way I found to re-set the board to "normal" is to select "Stripboard" again as the default.

It's no big deal as the blank area serendipity is probably worth the very minor bother.
Back to top
 
 
IP Logged
 
Mnementh
YaBB Newbies
*
Offline


Your message here...

Posts: 12
Dundee, Scotland
Re: Trackless holding area for components
Reply #7 - Apr 9th, 2016 at 5:04pm
 
Hi again,
I've noticed another problem when you make alterations to the track lengths.

It basically "kills" all the ROUTE features !

The ROUTE menu"Greys out" and even re-setting the track lengths back to "normal" does NOT enable the ROUTE functions again.

No big deal if all you're doing is a fairly simple board that you can route manually but worth noting.

Sandy.
Back to top
 
 
IP Logged
 
Page Index Toggle Pages: 1
Send Topic Print